Reply To: Which PCIe wlan cards are supported?

[Boris]

I tested with an ath10k card (same behavior like leothrix) and with a BCM94313 card. Only the BCM94313 card is recognized in the PCI bus.

—————-

BCM94313 card:

# Booting Trusted Firmware
BL1: v1.2(release):armada-17.02.0:
BL1: Built : 09:41:56, Jun 2 2NOTICE: BL2: v1.2(release):armada-17.02.0:
NOTICE: BL2: Built : 09:41:57, Jun 2 20NOTICE: BL31: v1.2(release):armada-17.02.0:
NOTICE: BL31:

U-Boot 2015.01-armada-17.02.0-g8128e91 (Jun 02 2017 – 09:41:51)

I2C: ready
DRAM: 1 GiB
Board: DB-88F3720-ESPRESSOBin
CPU @ 1000 [MHz]
L2 @ 800 [MHz]
TClock @ 200 [MHz]
DDR @ 800 [MHz]
Comphy-0: PEX0 2.5 Gbps
Comphy-1: USB3 5 Gbps
Comphy-2: SATA0 5 Gbps
Now running in RAM – U-Boot at: 3ff2b000
U-Boot DT blob at : 000000003fa18168
MMC: XENON-SDHCI: 0
SF: Detected W25Q32DW with page size 256 Bytes, erase size 4 KiB, total 4 MiB
PCIE-0: Link up (Gen1-x1 2.5GHz, Bus0)
SCSI: SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs
Net: neta0
Hit any key to stop autoboot: 0
Marvell>> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x14e4 0x4727 Network controller 0x80

—————–

ath10k card

Booting Trusted Firmware
BL1: v1.2(release):armada-17.02.0:
BL1: Built : 09:41:56, Jun 2 2NOTICE: BL2: v1.2(release):armada-17.02.0:
NOTICE: BL2: Built : 09:41:57, Jun 2 20NOTICE: BL31: v1.2(release):armada-17.02.0:
NOTICE: BL31:

U-Boot 2015.01-armada-17.02.0-g8128e91 (Jun 02 2017 – 09:41:51)

I2C: ready
DRAM: 1 GiB
Board: DB-88F3720-ESPRESSOBin
CPU @ 1000 [MHz]
L2 @ 800 [MHz]
TClock @ 200 [MHz]
DDR @ 800 [MHz]
Comphy-0: PEX0 2.5 Gbps
Comphy-1: USB3 5 Gbps
Comphy-2: SATA0 5 Gbps
Now running in RAM – U-Boot at: 3ff2b000
U-Boot DT blob at : 000000003fa18168
MMC: XENON-SDHCI: 0
SF: Detected W25Q32DW with page size 256 Bytes, erase size 4 KiB, total 4 MiB
advk_pcie_pio_read_config(227): wait for PIO time out
advk_pcie_pio_read_config(227): wait for PIO time out
PCIE-0: Link up (Gen1-x1 2.5GHz, Bus0)
SCSI: SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs
advk_pcie_pio_read_config(227): wait for PIO time out
advk_pcie_pio_read_config(227): wait for PIO time out
advk_pcie_pio_read_config(227): wait for PIO time out
advk_pcie_pio_read_config(227): wait for PIO time out
advk_pcie_pio_read_config(227): wait for PIO time out
Non-posted PIO Response Status: CA, 0xe00 @ 0xc
Non-posted PIO Response Status: CA, 0xe00 @ 0x1000
Non-posted PIO Response Status: CA, 0xe00 @ 0x1000
Non-posted PIO Response Status: CA, 0xe00 @ 0x2000
Non-posted PIO Response Status: CA, 0xe00 @ 0x2000
Non-posted PIO Response Status: CA, 0xe00 @ 0x3000
Non-posted PIO Response Status: CA, 0xe00 @ 0x3000
Non-posted PIO Response Status: CA, 0xe00 @ 0x4000
Non-posted PIO Response Status: CA, 0xe00 @ 0x4000
Non-posted PIO Response Status: CA, 0xe00 @ 0x5000
Non-posted PIO Response Status: CA, 0xe00 @ 0x5000
Non-posted PIO Response Status: CA, 0xe00 @ 0x6000
Non-posted PIO Response Status: CA, 0xe00 @ 0x6000
Non-posted PIO Response Status: CA, 0xe00 @ 0x7000
Non-posted PIO Response Status: CA, 0xe00 @ 0x7000
Non-posted PIO Response Status: CA, 0xe00 @ 0xc
Non-posted PIO Response Status: CA, 0xe00 @ 0x0
Non-posted PIO Response Status: CA, 0xe00 @ 0x0
Net: neta0
Hit any key to stop autoboot: 0
Marvell>> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
Non-posted PIO Response Status: CA, 0xe00 @ 0x0